Catalog FORMAT Plus- 2017 - 2018

Reamers 159

Hand cone reamer

Design: HSS, DIN 9-B with left spiral approx. 7°. The uneven tooth pitch ensure chatter-free and accurate drilling. With cylinder shank with square drive. Bright surface Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single production or repair work. Also suitable for holes with interrupted cut. Pre-drill with a cylindrical spiral drill or pin drill. Particularly suitable for steels up to 500 N/mm 2 in strength such as non-ferrous metals,

DIN 9-B

HSS

approx. 7°

Cutting Tools 1

1:50

plastics, steels up to 1000 N/mm 2 amd casting materials. Note: Tap wrenches for manual actuation – see Ç 1/223.

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1508

C

C

V

V

V

U

U

U

1508

Nominal ∅

Order No.

Small/large ∅

Cutting length

Total length

Width of keys

mm

mm

mm 58 68 73 105 145 175 210 210 210 230 250

mm 80 93 100 135 180 215 255 255 255 280 310

mm

bright

0300 0400 0500 0600 0800 1000 1200 1300 1400 1600 2000

3 4 5 6 8

19.30 21.90 23.00 27.90 43.20 61.00 77.60 90.30 95.40

2.90/ 4.06 3.90/ 5.26 4.90/ 6.36 5.90/ 8.00 7.90/10.80 9.90/13.40 11.80/16.00 12.80/17.00 13.80/18.00 15.80/20.40 19.80/24.80

3.0 3.8 4.9 6.2 8.0

10 12 13 14 16 20

10.0 11.0 12.0 12.0 14.5 18.0

107.50 140.00 (W140)

Machine cone reamer

Design: HSS, DIN 2179 with left spiral approx. 45°. The uneven tooth pitch ensure chatter-free and accurate drilling. With cylinder shank Bright surface Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single and serial production. Optimum angle accuracy for the reamed hole when using a floating reamer chuck. Pre-drill with a pin drill (order no. 1052). Particularly suitable for steels up to 500 N/mm 2 in strength such as non-ferrous metals, plastics, steels up to 1000 N/mm 2 amd casting materials.

DIN 2179 approx. 45°

HSS-E

1:50

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1510

C

C

V

V

V

U

U

U

1510

Nominal ∅

Order No.

Small/large ∅

Cutting length

Total length

Shank ∅ h9

mm

mm

mm

mm 86 86 100 112 122 160 207 245 290

mm

bright

0200 0250 0300 0400 0500 0600 0800 1000 1200

2.0 2.5 3.0 4.0 5.0 6.0 8.0

24.80 29.60 27.00 27.30 29.00 33.20 49.50 63.40 79.20 (W140)

1.90/ 2.86 2.40/ 3.36 2.90/ 4.06 3.90/ 5.26 4.90/ 6.36 5.90/ 8.00 7.90/10.80 9.90/13.40 11.80/16.00

48 48 58 68 73

3.15 3.15 4.00 5.00 6.30 8.00

105 145 175 210

10.00 12.50 16.00

10.0 12.0

1/141

Articles marked ◊ are not held in stock, procurement is effected at short notice.