Catalog FORMAT plus - EDE 2015 - 2017

Reamers 150

Hand reamer, quick adjustment

Design: Right cutting, with replaceable blades made of HSS, factory standard and cylinder shank with square drive. The uneven blade pitch ensure chatter-free and accurate drilling. The reamer can be progressively set within the stated adjustment range. The setting should be made using a ring gauge (order no. 4411). Bright surface Application: Particularly suitable for repair work. Only for reaming through-holes. Not suitable for machining blind holes due to the head screw. Particularly suitable for steel materials up to 500 N/mm 2 in strength e.g. general construction steels, steel materials up to 900 N/mm 2 in strength such as machine steels, tempered steels, tool steels, case-hardening steels, casting materials and non-ferrous metals such as aluminium, brass, copper and bronzes. Note: Tap wrenches for manual actuation – see Ç 1/220.

Factory standard

HSS

1 Cutting Tools

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1505

C

V

V

V

V

1505

Nominal ∅ d 1

Order No.

Adjustment range ∅ mm 6.4– 7.2 7.2– 8.0 8.0– 9.0 39.0–10.0 10.0–11.0 11.0–12.0 12.0–13.5 13.5–15.5 15.5–18.0 18.0–21.0 21.0–24.0 24.0–27.5 27.5–31.5 31.5–37.0 37.0–45.0 45.0–55.0

Overall length l 1 mm

Cutting edge length l 2 mm

Width of keys mm

Number of blades

mm 6.4 7.2 8.0 9.0 10.0 11.0 12.0 13.5 15.5 18.0 21.0 24.0 27.5 31.5 37.0 45.0

bright

0100 0105 0110 0115 0120 0125 0130 0135 0140 0145 0150 0155 0160 0165 0170 0175

69.90 69.90 69.90 73.40 73.40 73.40 82.50 93.10 95.40

110 110 115 115 115 125 135 146 166 178 195 218 245 280 325 370

32 32 34 34 34 35 41 50 60 65 76 82 86 98 108 118

3.0 3.4 3.8 4.3 4.9 4.9 6.2 7.0 8.0 9.0 11.0 12.0 14.5 18.0 20.0 26.0

4 4 5 5 5 5 5 5 5 5 5 5 5 6 6 6

103.50 124.50 131.50 161.50 225.50 292.00 395.00

(141)

Hand cone reamer Design: HSS, DIN 9-B with left spiral approx. 7°. The uneven tooth pitch ensure chatter-free and accurate drilling. With cylinder shank with square drive. Bright surface Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single production or repair work. Also suitable for holes with interrupted cut. Pre-drill with a cylindrical spiral drill or pin drill. Particularly suitable for steels up to 500 N/mm 2 in strength such as non-ferrous metals,

DIN 9-B

HSS

approx. 7°

1:50

plastics, steels up to 1000 N/mm 2 amd casting materials. Note: Tap wrenches for manual actuation – see Ç 1/220.

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1508

C

C

V

V

V

V

V

U

U

U

1508

Nominal ∅

Order No.

Small/large ∅

Cutting length

Total length

Width of keys

mm

mm

mm 58 68 73 105 145 175 210 210 210 230 250

mm 80 93 100 135 180 215 255 255 255 280 310

mm 3.0 3.8 4.9 6.2 8.0 10.0 11.0 12.0 12.0 14.5 18.0

bright

0300 0400 0500 0600 0800 1000 1200 1300 1400 1600 2000

3 4 5 6 8

18.85 21.40 22.50 27.20 42.10 59.50 75.70 88.10 93.10

2.90/ 4.06 3.90/ 5.26 4.90/ 6.36 5.90/ 8.00 7.90/10.80 9.90/13.40 11.80/16.00 12.80/17.00 13.80/18.00 15.80/20.40 19.80/24.80

10 12 13 14 16 20

105.00 136.50

(140)

1/130

All stocked articles available within 24 hours by UPS Express.

All prices excluding VAT per piece (if not stated otherwise).