Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro

Countersink tools 131

Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase. 90° countersinks and deburring countersinks with cylinder with uneven pitch

m

Design: With radial taper, uneven pitch and straight clamping slots. Also provided with cutting and clearance angles for the most common materials. Application: The strong uneven pitch allows a particularly smooth run when countersinking meaning that the surface is cleaner and that the cutting load is reduced to a minimum. Suitable for countersinking and deburring work for countersunk screws DIN 963, DIN 964, DIN 965, and DIN 966 in one step.

DIN 335-C

Z 3

HSS

Cutting Tools 1

90°

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1428

C

C

V

V

C

1428

Nominal ∅

Order No.

Smallest ∅

Total length

Shank ∅

mm 4.3 6.0 6.3 8.0 8.3 10.0 10.4 11.5 12.4 15.0 16.5 19.0 20.5 23.0 25.0 31.0

mm 1.3 1.5 1.5 2.0 2.0 2.5 2.5 2.8 2.8 3.2 3.2 3.5 3.5 3.8 3.8 4.2

mm

mm

ZrN

0430 0600 0630 0800 0830 1000 1040 1150 1240 1500 1650 1900 2050 2300 2500 3100

18.95 20.20 20.40 22.10 22.50 23.00 23.20 26.30 27.60 31.20 31.80 35.20 39.60 43.40 47.80 58.50 (W141)

40 45 45 50 50 50 50 56 56 60 60 63 63 67 67 71

4 5 5 6 6 6 6 8 8

ZrN

10 10 10 10 10 10 12

m

90° countersinks and deburring countersinks set with cylinder with uneven pitch

Design: Supplied in a plastic box. Note: Set consisting of (Order No. 1058). Bonus price due to set compilation.

1428

Set contents

Order No.

mm

ZrN

0010

6.3; 10.4; 16.5; 20.5; 25.0

156.50 (W141)

ZrN

90° manual deburrer

Design: HSS, DIN 335-D, 90° countersink angle. Axial and radial taper-ground and CBN deep-ground, bright surface With straight clamping slots and drilling spaces ground from full pieces. Also provided with cutting and clearance angles for the most common materials as well as a user-friendly 2-component handle. Application: For drilling, countersinking and deburring work by hand for countersunk screws DIN 963, DIN 964, DIN 965 and DIN 966 and DIN 7991.

DIN 335-D

Z 3

HSS

90°

1468

Nominal ∅

Order No.

mm 12.4 15.0 16.5 20.5 25.0

bright

1250 1500 1650 2050 2500

19.25

22.40 m

22.40 26.90 32.70 (W134)

bright

1/113

Articles marked ◊ are not held in stock, procurement is effected at short notice.