Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro

Grinding wheel dressers 1353

Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.

Diamond grinding wheel dressing tool

Design: With approx. 48 single, set diamonds of approx. 3.5 carats in 4 rows, firmly embedded in the working surface, with plastic handle.

Application: Defining and honing aluminium oxide grinding wheels by hand. Suitable for dry use.

8533

8536

Diamond-studded head 180°

Diamond-studded head 90°.

8533

8536

8533

Abrasive surface mm

Order No. 0005

Total length mm

40 x 10

94.50 (W859)

94.50 (W859)

220

8536

Diamond single point dressing tool

Design: Shaft mounted single- or one-stone abrasive diamond block, solid-shaped crystal with few occlusions or irregular cracking, no crevices. Application: For profiling e.g. abrasives for all ceramic-bonded grinding wheels. The abrasive is always clamped so that the angle to the middle of the grinding wheel is between 5° and 15°. Dressing work with

diamonds is better wet and with plenty of ventilation as they are sensitive to shock and temperature. As the diamond becomes progressively blunt it should be twisted 90°. Note: The choice of the right diamond size depends on the ∅ of the grinding wheel, e.g. the wheel width. Worn diamond abrasives should be regularly replaced.

From 1.5 carats with remote head

8512

8512

Diamond size/ carat weight

Diamond size/ carat weight

Order No.

Design

For grinding wheel ∅ to mm

Order No.

Design

For grinding wheel ∅ to mm

0025 0050 0075 0100 1025 1050 1075

0.25 34.30 0.50 60.10 0.75 97.70 1.00 141.50 0.25 34.30 0.50 60.10 0.75 97.70

MK0 MK0 MK0 MK0 MK1 MK1 MK1

150 300 400 500 150 300 400

1100 1150 2025 2050 2075 2100 2150

1.00 141.50 1.50 198.00

MK1 MK1

500 750

0.25 34.30 * Shaft cyl. ∅ 8 x 80 mm 150 0.50 60.10 * Shaft cyl. ∅ 8 x 80 mm 300 0.75 97.70 * Shaft cyl. ∅ 8 x 80 mm 400 1.00 141.50 * Shaft cyl. ∅ 8 x 80 mm 500 1.50 198.00 * Shaft cyl. ∅ 8 x 80 mm 750 (W859)

* Other sizes available upon request.

(W859)

Diamond multi-point dressing tool

Design: 5 diamonds, in a special sintered binding, so that they can be used right to the end without changing. Application: The diamond multi-point dressing tool is a practical dressing tool for

coarse grinding with wheels of all diameters up to 100 grit. Note: To prolong the life of this sharpener, continuous cooling should be used during the dressing process.

8515

8515 8518

8521

MK0. Total length 40 mm.

Shaft cyl. ∅ 8 x 80 mm.

8518

MK1. Total length 57 mm.

8518

8521

8515

Diamond content/ carat weight approx.

Order No. 0005

1.00

107.50 (W859)

107.50 (W859)

107.50 *

8521

(W859)

* Other sizes and shapes available upon request.

Diamond multi-point dressing tool

Abrasives 8

Design: Single-sintered, high-concentrate (2.5 carat) diamond grain. Diamond cylinder set in the shaft (so no loss of diamonds), universal type. Application: Because of the multiple working points on an efficient diamond tool sharpener, it is only for straight grinding wheel surfaces (flat and peripheral edge). These abrasives

have no gradient, so the whole of the diamond grit is employed. This type is not resettable, it is durable and can be used until worn. Not suitable for detail work. For use with disc wheel 36-120. Note: Adequate cooling before and during the dressing process maximises its life span.

8524

8524 8527

8530

MK0. Total length 40 mm.

Shaft cyl. ∅ 10 x 80 mm.

8527

MK1. Total length 57 mm.

8527

8530

8524

Diamond content/ carat weight approx.

Order No. 0005

Diamond inset ∅ mm

2.50

63.90 (W859)

63.90 (W859)

63.90 *

8

8530

(W859)

* Other sizes and shapes available upon request.

8/5

Articles marked ◊ are not held in stock, procurement is effected at short notice.