Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro

Thread cutting tools 197

Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.

Threading tool assortment HexTap

Roughing tap with pilot pin

Finish tap

Cutting Tools 1

Inner hexagon for ratchet or angled screwdriver

Outer hexagon for open-end wrench

Application: for general use • Easy to machine materials up to 900 N/mm 2

Benefits: • Pilot pins for accurately aligned fixing • Roughing and finish tap in one tool • Use for difficult to access areas • For producing new threads • For drilling and repairing damaged threads

• Non-alloyed and low alloy steels • For through-holes and blind holes • For manual use

Cutting tap bit HexTap S

Design: Tap bit, 1/4" hexagonal mount for pipe threads according to DIN ISO 228. Application: Cutting tap bits are designed for thread drilling with cordless screw drills and handheld drills with left and right motion. However, they are also suitable for drilling by hand and on stationary drilling machines. Your cordless screw drill should have a minimum power of 7.5 Volt. Make sure that the tool axis and hole axis are precisely aligned and use appropriate cutting oil.

DIN ISO 228

G

HSS

1/4"

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1649

C

V

1649

Nominal ∅ inch

Order No. 0250

Total length mm

Cutting length mm

Width of keys mm

G 1/8

6.90

40.5

17

6.35

(W161)

Cutting tap bit HexTap DS

Design: Double-sided tap Multi-Drive for metric ISO thread according to DIN 13. Application: For general use in materials with good machining properties up to 900 N/mm 2 . For non-alloy and low alloy steels, through-holes and blind holes The tap is designed for manual use.

DIN 13

M

HSS

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1649

C

V

1649

Nominal ∅ mm

Order No. 0120 0140 0160 0180 0200

Overall length l 1 mm

Cutting edge length l 2 mm

Wrench size 1 mm

Wrench size 2 mm

M12 M14 M16 M18 M20

14.95 17.20 19.50 21.80 24.10 (W161)

70 70 70 80 80

22 22 22 24 24

8

4 4 4 5 6

10 10 13 13

1/179

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Made with FlippingBook Online document