Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro
Hole thread milling cutter 253
Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.
Design: Ultra-finest grain-solid carbide, with internal supply of coolant and 27° right spiral slots to achieve optimum cutting conditions as well as with 45° countersink bevel. The milling principle results in an exact thread depth, a very high surface quality in the thread, process- reliable machining of difficult to cut materials and thread production very close down to the base. Application: For drilling, countersinking and thread cutting with a single tool. For regular metric threads (both right and left thread) according to ISO DIN 13 for through-holes and blind holes. Note: Solid carbide tap milling cutter for additional thread types (UNC, UNF, pipe thread etc.) on request. You will further information in the technical appendix. Solid carbide tap drill DTMC-SP for inner thread
Solid carbide
M
DIN 6535-HA
60°
45°
27°
Cutting Tools 1
1,5xd
l6
l1
45 o
140 o
d K
d2
d3
d1
l2
l3
TiCN
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Copper, brass, bronze
Cast iron materials
Al, Al and Mg alloys
Order No. 1897
120
200
200
1897
Thread
Order No.
Gradient
Cutting edge length l 2 mm
Shank ∅ d 2 mm l 3 mm l 6 mm D 3 mm d k mm Number of slots
Overall length l 1 mm
mm
TiCN
0004 0005 0006 0008 0010 0012 0014 0016
M4 M5 M6 M8
354.50 ◊ 350.00 ◊ 353.00 ◊ 410.50 ◊ 468.00 ◊ 612.50 ◊ 778.00 ◊ 879.00 ◊
0.70 0.80 1.00 1.25 1.50 1.75 2.00 2.00
6.9 8.7 10.9 13.7 18.0 20.8 23.6 26.0
48 54 62 74 80 90 102 102
6 6 8
36 36 36 40 45 45 48 48
0.70 0.80 1.00 1.25 1.50 1.50 1.50 1.50
4.5 5.5 6.6 9.0 11.0 13.5 15.5 17.5
3.3 4.2 5.0 6.8 8.5 10.2 12.0 14.0
2 2 2 2 2 2 2 2
10 12 14 16 18
M10 M12 M14 M16
(W175)
Design: Ultra-finest grain-solid carbide, with internal supply of coolant and 27° right spiral slots to achieve optimum cutting conditions as well as with 45° countersink bevel. The milling principle results in an exact thread depth, a very high surface quality in the thread, process- reliable machining of difficult to cut materials and thread production very close down to the base. Application: For drilling, countersinking and thread cutting with a single tool. For regular metric threads (both right and left thread) according to ISO DIN 13 for through-holes and blind holes. Note: VHM tap milling cutter for additional thread types (UNC, UNF, pipe thread etc.) on request. You will further information in the technical appendix. VHM thread milling cutter DTMC-SP for inner thread
Solid carbide
M
DIN 6535-HA
60°
45°
27°
2xd
l6
l1
45 o
140 o
d K
d2
d3
d1
l2
l3
TiCN
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Copper, brass, bronze
Cast iron materials
Al, Al and Mg alloys
Order No. 1899
120
200
200
1899
Thread
Order No.
Gradient
Cutting edge length l 2 mm
Shank ∅ d 2 mm l 3 mm l 6 mm D 3 mm d k mm Number of slots
Overall length l 1 mm
mm
TiCN
0004 0005 0006 0008 0010 0012 0014 0016
M4 M5 M6 M8
354.50 ◊ 350.00 ◊ 353.00 ◊ 410.50 ◊ 468.00 ◊ 612.50 ◊ 778.00 ◊ 879.00 ◊
0.70 0.80 1.00 1.25 1.50 1.75 2.00 2.00
9.0 11.1 13.9 18.7 22.5 26.1 31.6 36.0
48 54 62 74 80 90 102 102
6 6 8
36 36 36 40 45 45 48 48
0.70 0.80 1.00 1.25 1.50 1.50 1.50 1.50
4.5 5.5 6.6 9.0 11.0 13.5 15.5 17.5
3.3 4.2 5.0 6.8 8.5 10.2 12.0 14.0
2 2 2 2 2 2 2 2
10 12 14 16 18
M10 M12 M14 M16
(W175)
1/235
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Made with FlippingBook Online document