html-Catalog FORMAT plus - EDE 2015 - 2017

123

Circle cutter and accessories

Cross hole countersink, 90°

Design: HSS, 90° countersink angle, with cylinder shank. With evenly running special taper-ground in the cone coat. The good blade geometry results in a light, spiral cut. The chips are pushed up in the shank direction by the inclined hole and cannot damage the countersink. This makes the countersink round and protects the machine spindle. Application: Suitable for light and chatter-free hole deburring and countersinking.

HSS Z 1

90°

Particularly suitable for long chipping materials. Sharpening is possible by simply resharpening using an abrasive pencil on the blade front. Spiral fluted with fixed pilot pin

1 Cutting Tools

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1424

C

V

C

V

C

C

1424

Countersink area mm

Order No. 0100 0140 0210 0275 0350 0440 0480 0530 0640

Total length mm

Shank ∅ mm

Head ∅ mm

2– 5 5–10 10–15 15–20 20–25 25–30 30–35 35–40 40–50

6.95 8.75

45 48 65 84 102 115 127 136 166

6 8

10 14 21 28 35 44 48 53 60

15.30 27.70 36.20 48.20

10 12 12 15 15 15 20

72.10 m 100.00 m 143.00 m

(134)

Cross hole countersink set, 90°

Design: Supplied in a robust, high quality plastic cassette with automatic countersink setup function when opened.

1427

Set consisting of: (order no. 1424).

Set contents mm

Order No. 0001

2–5; 5–10; 10–15; 15–20

84.90 (134)

Cross hole countersink, 90°

Design: HSS, Co5. 90° countersink angle. With evenly running special taper-ground in the cone coat. The good blade geometry results in a light, spiral cut. The chips are pushed up in the shank direction by the inclined hole and cannot damage the countersink. This makes the countersink round and protects the machine spindle. Application: Suitable for light and chatter-free hole deburring and countersinking. Equally suitable for almost all materials due to the excellent cutting properties. Sharpening is possible by simply resharpening using an abrasive pencil on the blade front.

HSS Co5

Z 1

90°

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1425

C

V

C

U

C

U

1425

Countersink area mm

Order No. 0100 0140 0210 0275 0350 0440 0480 0530 0640

Total length mm

Shank ∅ mm

Head ∅ mm

2– 5 5–10 10–15 15–20 20–25 25–30 30–35 35–40 40–50

8.00

45 48 65 84 102 115 127 136 166

6 8

10 14 21 28 35 44 48 53 60

10.30 17.85 32.60 43.60 56.80

10 12 12 15 15 15 20

101.00 m 136.00 m 220.00 m

(134)

90° cross hole countersink set

Design: Supplied in a robust, high quality plastic cassette with automatic countersink setup function when opened.

1427

Set consisting of: (order no. 1425).

Set contents mm

Order No. 0005

2–5; 5–10; 10–15; 15–20

99.90 (134)

1/103

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.