html-Catalog FORMAT plus - EDE 2015 - 2017

129

Circle cutter and accessories

Countersinks and deburring countersinks 90° ASP

Design: HSS-E PM, ASP2030 ® , DIN 335-C. 90° countersink angle. Axial and radial taper-ground and CBN deep-ground, bright. With straight, u-shaped clamping slots and drilling spaces ground from full pieces. Also provided with cutting and clearance angles for the most common materials. Application: Particularly suitable for the highest loads in INOX steel, stainless steel and Hardox. Suitable for universal chatter and burr-free drilling, countersinking and deburring work for countersunk screws DIN 963, DIN 964, DIN 965, DIN 966 and DIN 7991 in one step. Please note the large countersink range! The excellent cutting properties and easy machining process result from the cone-shaped back taper on the coat and angle of rake. The countersink achieves the best results with the strongest feed and lowest cutting speed. Note: Sufficient supply of coolant is essential. HSS-E PM has, in comparison to conventional

HSS-E PM

DIN 335-C

Z 3

1 Cutting Tools

90°

HSS steels, a consistent, fine grained material structure. This means they have good hot hardness, pressure resistance and resistance to wear.

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1448

C

C

V

C

V

1448

Nominal ∅

Order No.

Smallest ∅

Total length

Shank ∅

mm 6.3 8.3 10.4 12.4 16.5 20.5 25.0 31.0 40.0

mm 1.5 2.0 2.5 2.8 3.2 3.5 3.8 4.2 5.0

mm

mm

bright

0630 0830 1040 1240 1650 2050 2500 3100 4000

15.00 17.20 19.70 25.50 33.40 45.30 63.60 98.10

45 50 50 56 60 63 67 71 80

5 6 6 8

bright

10 10 10 12 15

149.50 m

(134)

Countersinks and deburring countersinks set 90° ASP

Set consisting of (order no. 1448).

1448

Set contents mm

Order No. 0005 0010

6.3; 8.3; 10.4; 12.4; 16.5; 20.5 6.3; 10.4; 16.5; 20.5; 25.0

135.00 173.50 (134)

90° countersinks and deburring countersinks, carbide

Design: K20 carbide, DIN 335-C. 90° countersink angle. Axial and taper-ground and CBN deep- ground. With straight, u-shaped clamping slots and drilling spaces ground from full pieces. For tough materials such as Hardox 400/500, steels up to 60 HRC. Application: The excellent cutting properties and easy machining process result from the cone- shaped back taper on the coat and angle of rake. The countersink achieves the best results with

DIN 335-C

Z 3

Carbide

the strongest feed and lowest cutting speed. Note: Sufficient supply of coolant is essential.

90°

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1447

C

C

C

C

C

C

C

C

C

V

1447

Nominal ∅ mm

Order No. 0630 0830 1040 1240 1650 2050 2500 3100

Smallest ∅ mm

Total length mm

Shank ∅ mm

6.3 8.3 10.4 12.4 16.5 20.5 25.0 31.0

73.30 74.40 76.10 76.80 89.10

2.2 2.8 3.5 4.0 5.0 7.0 9.0 11.0

45 50 50 56 60 63 67 71

5 6 6 8

10 10 10 12

117.50 158.50 219.00

(136)

With morse taper shank available on request.

90° countersinks and deburring countersinks set, carbide

Set consisting of (order no. 1447).

1447

Set contents mm

Order No. 0005 0010

6.3; 8.3; 10.4; 12.4; 16.5; 20.5 6.3; 10.4; 16.5; 20.5; 25.0

436.00 546.50 (136)

1/109

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.