html-Catalog FORMAT plus - EDE 2015 - 2017

1313

Grinding wheel dressers

Diamond grinding wheel dressing tool

Design: With ca. 48 single, set diamonds of ca. 3.5 carats in 4 rows, firmly embedded in the working surface, with plastic handle. Application: Defining and honing aluminium oxide grinding wheels by hand. Suitable for dry use.

8533 8536

Diamond-studded head 180°

Diamond-studded head 90°.

8533

8536

8533

Abrasive surface mm

Order No. 0005

Total length mm

40 x 10

92.20

92.20

220

8536

(859)

(859)

Diamond single-point dressing tool

Design: Shank mounted single- or one-stone abrasive diamond block, solid-shaped crystal with few occlusions or irregular cracking, no crevices. Application: For profiling e.g. abrasives for all ceramic-bonded grinding wheels. The abrasive is always clamped so that the angle to the middle of the grinding wheel is between 5° and 15°. Dressing work with diamonds is better wet and with plenty of ventilation as they are sensitive to shock and temperature. As the diamond becomes progressively blunt it should be twisted 90°. Note: The choice of the right diamond size depends on the ∅ of the grinding wheel, e.g. by the disc width. Worn diamond abrasives should be regularly replaced.

From 1.5 carats with remote head

8512

8512

Diamond size/ carat weight

Diamond size/ carat weight

Order No.

Design

For grinding wheel-∅ to mm

Order No.

Design

For grinding wheel-∅ to mm

0025 0050 0075 0100 1025 1050 1075

0.25 0.50 0.75 1.00 0.25 0.50 0.75

33.40 58.40 95.20 138.00 33.40 58.40 95.20

MK0 MK0 MK0 MK0 MK1 MK1 MK1

150 300 400 500 150 300 400

1100 1150 2025 2050 2075 2100 2150

1.00 1.50 0.25 0.50 0.75 1.00 1.50

138.00 192.50 33.40 * 58.40 * 95.20 * 138.00 * 192.50 *

MK1 MK1

500 750

Shank cyl. ∅ 8 x 80 mm 150 Shank cyl. ∅ 8 x 80 mm 300 Shank cyl. ∅ 8 x 80 mm 400 Shank cyl. ∅ 8 x 80 mm 500 Shank cyl. ∅ 8 x 80 mm 750

(859)

(859)

* Other sizes available upon request.

Diamond-multi-point dressing tool

Design: 5 diamonds, in a special sintered binding, so that they can be used right to the end without changing. Application: The diamond-multi-point dressing tool is a practical smoothing tool for coarse grinding with wheels of all diameters, up to 100 grit. Note: To prolong the life of this sharpener, continuous cooling should be used during the dressing process.

8515

8515 8518

MK0. Total length 40 mm.

8518

8521

Shank cyl. ∅ 8 x 80 mm.

MK1. Total length 57 mm.

8518

8521

8515

Diamond content/carat weight ca.

Order No. 0005

1.00

107.50

107.50

107.50 *

8521

(859)

(859)

(859)

* Other sizes available upon request.

Diamond multi-point dressing tool

8 Abrasives

Design: Single-sintered, high-concentrate (2.5 carat) diamond grain. Diamond cylinder set in the shank (so no loss of diamonds), universal type. Application: Because of the multiple working points on an efficient diamond tool sharpener it is only for straight-grinding wheelsurfaces (flat- and peripheral edge). These abrasives have no gradient, so the whole of the diamond grit is employed. This type is not resettable, it is durable and can be used until worn. Not suitable for detail work. For use with wheelgrit 36–120. Note: Adequate cooling before and during the smoothing process maximises its life span.

8524

8524 8527

MK0. Total length 40 mm.

8527

8530

Shank cyl. ∅ 10 x 80 mm.

MK1. Total length 57 mm.

8527

8530

8524

Diamond content/ carat weight ca.

Order No.

Diamond inset ∅ mm

0005

2.50

63.90

63.90

63.90 *

8

8530

(859)

(859)

(859)

* Other sizes available upon request.

8/5

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.