html-Catalog FORMAT plus - EDE 2015 - 2017

149

Reamers

Hand reamer, adjustable

Design: HSS, DIN 859, form B, with cylinder shank and square drive. The uneven tooth pitch ensure chatter-free and accurate drilling. The body of the reamer is slotted, the nominal ∅ can be increased to approx. 1/100 by turning the head screw in. The setting should be made using a ring gauge (order no. 4411). All required adaptations can be set and wear compensated. Reamers are set to the nominal size. Store depressurised. The ∅ 4 and 5 mm are straight fluted, spiral fluted from ∅ 6 mm (left spiral 7°). Application: Perfectly suited for single production or repair work, only for reaming through- holes. Not suitable for machining blind holes due to the conical point geometry and head screw. Also suitable for holes with interrupted cut. Particularly suitable for steel materials up to 500 N/mm 2 in strength e.g. general construction steels, steel materials up to 900 N/mm 2 in strength such as machine steels, tempered steels, tool steels, case-hardening steels, casting materials and non-ferrous metals such as aluminium, brass, copper and bronzes. Note: The hand reamer is sensitive to impacts and chips should therefore not be knocked out, but blown or washed out. Tap wrenches for manual actuation see page Ç 1/220.

DIN 859

Form B

HSS

1 Cutting Tools

approx. 7°

ø

ø

bright

ø

ø

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1504

C

V

V

V

V

1504

1504

Nominal ∅ d 1 mm

Nominal ∅ d 1 mm

Order No.

Overall length l 1 mm

Cutting edge length l 2 mm

Order No.

Overall length l 1 mm

Cutting edge length l 2 mm

Shank ∅ d 2 mm

Shank ∅ d 2 mm

bright

bright

0400 0500 0600 0700 0800 0900 1000 1100 1200 1300

4.0* 5.0*

50.80 51.20 51.20 62.80 61.80 66.40 67.60 81.50 76.70 89.60

76 87 93 107 115 124 133 142 152 152

24 30 33 38 42 46 50 51 56 56

4 5 6 7 8 9

1400 1500 1600 1800 1900 2000 2200 2400 2500 3000

14.0 15.0 16.0 18.0 19.0 20.0 22.0 24.0 25.0 30.0

92.10 94.30

163 163 175 188 188 201 215 231 231 247

61 61 67 68 68 75 82 85 85 94

14 15 16 18 19 20 22 24 25 30

6.0 7.0 8.0 9.0 10.0 11.0 12.0 13.0

117.50 123.50 126.50 130.00 156.00 171.00 171.00 222.00

10 11 12 13

(141)

(141)

* Straight fluted

m Limit plug gauge

for testing drilled holes is found on Ç 4/67.

1/129

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.

Made with