html-Catalog FORMAT plus - EDE 2015 - 2017
151
Reamers
Maschinen-Kegelreibahle chine con r amer
Design: HSS, DIN 2179 with left spiral approx. 45°. The uneven tooth pitch ensure chatter- free and accurate drilling. With cylinder shank. Bright surface. Application: For reaming conical holes for taper pins according to DIN 1, DIN 258, DIN 1447, DIN 7977 and DIN 7978. Perfectly suited for single and serial production. Optimum angle accuracy for the reamed hole when using a floating reamer chuck. Pre-drill with a pin drill (order no. 1052). Particularly suitable for steels up to 500 N/mm 2 in strength such as non-ferrous metals, plastics, steels up to 1000 N/mm 2 amd casting materials.
DIN 2179 approx. 45°
HSS-E
1 Cutting Tools
1:50
bright
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 60 HRC
Al, AI and Mg alloys
Copper, brass, bronze
Steels up to 56 HRC
Cast iron materials
Order No.
1510
C
C
V
V
V
V
V
U
U
U
1510
Nominal ∅
Order No.
Small/large ∅
Cutting length
Total length
Shank ∅ h9
mm 2.0 2.5 3.0 4.0 5.0 6.0 8.0 10.0 12.0
mm
mm 48 48 58 68 73 105 145 175 210
mm 86 86 100 112 122 160 207 245 290
mm
bright
0200 0250 0300 0400 0500 0600 0800 1000 1200
24.20 28.90 26.30 26.60 28.30 32.40 48.30 61.80 77.30
1.90/ 2.86 2.40/ 3.36 2.90/ 4.06 3.90/ 5.26 4.90/ 6.36 5.90/ 8.00 7.90/10.80 9.90/13.40 11.80/16.00
3.15 3.15 4.00 5.00 6.30 8.00 10.00 12.50 16.00
(140)
Rivet hole reamer
Design: HSS, DIN 311, with approx. 25° left spirals and long, conical point 1:10. The uneven tooth pitch ensure chatter-free and accurate drilling. With morse taper shank. Bright surface. Application: For correcting too small and offset holes. Particularly suitable for steel materials such as general construction steels, machine steels, tempered steels, case-hardening steels, tool steels, high speed steels, casting iron, nodular graphite iron and malleable cast iron, and soft non-ferrous metals such as aluminium and brass.
DIN 311
HSS
approx. 25°
MK 1–3
bright
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Al, AI and Mg alloys
Copper, brass, bronze
Cast iron materials
Order No.
1512
C
C
V
V
V
V
V
U
U
U
1512
Nominal ∅ k11
Order No.
Small ∅
Cutting length
First cut length
Total length
Number of teeth
MK
mm
mm 7.0 8.4 9.1 9.8 10.5 11.2 11.9 12.6 14.0 14.7 15.4 17.5 19.6 21.0
mm 95 105 105 115 125 135 135 145 155 155 165 180 195 195
mm
mm 171 199 199 209 219 229 251 261 271 271 281 296 311 311
bright
1000 1200 1300 1400 1500 1600 1700 1800 2000 2100 2200 2500 2800 3000
10 12 13 14 15 16 17 18 20 21 22 25 28 30
48.90 53.10 53.10 54.30 57.20 60.10 70.70 76.70 84.30 87.80 93.10
30 39 39 42 45 48 51 58 62 62 66 72 78 78
4 4 4 5 5 5 5 5 5 5 5 5 5 5
1 2 2 2 2 2 3 3 3 3 3 3 3 3
106.50 130.00 148.50
(140)
1/131
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Not all items are available in every country.
Made with FlippingBook