html-Catalog FORMAT plus - EDE 2015 - 2017

60

Drilling tools

Boring bush drill with Morse taper Shank

Design: HSS, DIN 341, type N. Profile grinding, steam tempered surface, right cutting, with precise point geometry. Good centring characteristics due to point thinning according to DIN 1412, form A. Angle of rake, core thickness and core gradient normal. Application: Suitable for drilling through boring bushes (important for sloped and uneven surfaces) as well as drilling deep holes up to 10 x D. Particularly suitable for alloyed and non-alloyed steels, steel casting, grey cast iron, malleable cast iron, nodular iron, sintered iron, nickel silver and graphite.

Type N

HSS DIN 341

MK 1–4 118°

25–30°

1 Cutting Tools

10xD

steam

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1089

22

22

6WHHOV XSWR

6WHHOV XSWR

1089

1089

∅ h8

∅ h8

Order No.

Spiral length mm

Total length mm

MK

Order No.

Spiral length mm

Total length mm

MK

1PP

1PP

f mm/rev

f mm/rev

mm 10.0 10.5 11.0 11.5 12.0 12.5 13.0 13.5 14.0 14.5 15.0 15.5 16.0 16.5 17.0 17.5 18.0 18.5 19.0 19.5 20.0 20.5 21.0

mm 21.5 22.0 22.5 23.0 24.0 25.0 26.0 27.0 28.0 29.0 30.0 31.0 32.0 33.0 34.0 35.0 36.0 37.0 38.0 39.0 40.0 45.0 50.0

steam

steam

1000 1050 1100 1150 1200 1250 1300 1350 1400 1450 1500 1550 1600 1650 1700 1750 1800 1850 1900 1950 2000 2050 2100

20.30 20.90 21.40 21.40 21.40 21.60 21.60 24.10 24.40 30.90 30.60 29.80 32.00 33.60 33.30 38.20 37.90 45.80 41.80 47.90 45.80 57.40 52.20

116 116 125 125 134 134 134 142 142 147 147 153 153 159 159 165 165 171 171 177 177 184 184

197 1 0.200 197 1 0.200 206 1 0.200 206 1 0.200 215 1 0.200 215 1 0.200 215 1 0.250 223 1 0.250 223 1 0.250 245 2 0.250 245 2 0.250 251 2 0.250 251 2 0.250 257 2 0.315 257 2 0.315 263 2 0.315 263 2 0.315 269 2 0.315 269 2 0.315 275 2 0.315 275 2 0.315 282 2 0.400 282 2 0.400

2150 2200 2250 2300 2400 2500 2600 2700 2800 2900 3000 3100 3200 3300 3400 3500 3600 3700 3800 3900 4000 4500 5000

61.80 56.90 62.80 59.10 72.60 73.20 84.00 90.00

191 191 198 198 206 206 214 222 222 230 230 239 248 248 257 257 267 267 277 277 277 298 321

289 2 0.400 289 2 0.400 296 2 0.400 296 2 0.400 327 3 0.400 327 3 0.400 335 3 0.400 343 3 0.400 343 3 0.400 351 3 0.400 351 3 0.400 360 3 0.400 397 4 0.500 397 4 0.500 406 4 0.500 406 4 0.500 416 4 0.500 416 4 0.500 426 4 0.500 426 4 0.500 426 4 0.500 447 4 0.630 470 4 0.630

100.50 116.00 115.50 152.50 161.00 161.00 202.00 196.00 225.50 255.00 243.00 260.50 272.50 457.00 457.00

(100)

(100)

Counterbore with Morse taper Shank

Design: HSS, DIN 343, type N. Profile grinding, steam tempered surface, right cutting. Normal angle of rake, normal core thickness and without core gradient. The spiral length is longer than the height of the bushes. Application: For drilling out pre-drilled, pre-cast or pre-punched holes. The sturdy construction and 3 blades means that alignment inaccura- cies and runouts in pre-drilled holes are corrected. Furthermore, the drill wall surface is improved so that a reamer can be subsequently used for perfect final reaming. Please pay attention to the column "smallest ∅ of pre-drilled hole". Note: The cut diameter must be smaller than the hole to be drilled out. Further dimensions or HSS-E designs or VHM/HM assembly or long flute counter bores according to DIN 1864 available on request.

Z 3

Type N

HSS DIN 343

MK 1–3 120°

22°

steam

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

1085

30

25

10

45

1085

1085

∅ h8

∅ h8

Order No.

Spiral length mm

Total length mm

Smallest ∅ of pre-drilled hole mm

Order No.

Spiral length mm

Total length mm

Smallest ∅ of pre-drilled hole mm

MK

MK

mm

mm

steam

steam

0780 0880 0980 1000 1075 1100 1175

7.80 35.10 8.80 48.80 ◊ 7.80 38.90 10.00 43.40 10.75 54.90 ◊ 11.00 38.90 11.75 41.20

75 156 81 162 87 168 87 168 94 175 94 175 101 182

5.6 6.3 7.0 7.0 7.7 7.7 8.4

1 1 1 1 1 1 1

1200 1275 1300 1375 1400 1475 1500

12.00 38.90 12.75 50.30 13.00 42.70 13.75 50.30 14.00 43.40 14.75 55.60 15.00 48.80

101 182 101 182 101 182 108 189 108 189 114 212 114 212

8.4 9.1 9.1 9.8 9.8 10.5 10.5

1 1 1 1 1 2 2

(109)

(109)

Continued overleaf

1/40

All stocked articles available within 24 hours by UPS Express.

All prices excluding VAT per piece (if not stated otherwise).