html-Catalog FORMAT plus - EDE 2015 - 2017
76
Drilling tools
Solid carbide centre drill
Design: solid carbide (K10/K20), according to factory standard. Profile grinding, bright surface, right cutting, with precise point geometry. Point thinning > ∅ 1.60 mm according to DIN 1412, form A. ∅ tolerance: on drill ∅ 1.00–2.5 = + 0.14 mm ∅ 3.15–5.0 = + 0.18 mm ∅ 6.30 = + 0.22 mm
Solid carbide K10/K20
60°
Factory standard
1 Cutting Tools
Application: For centring holes without protective countersinking. Particularly suitable for abrasive materials, AlSI alloys, fibre-reinforced plastics, duroplasts with a sanding effect on blades and fibres, high strength steels, steel castings, grey cast iron, hard castings, manganese hard steel, CrNi steels, bronzes and light and non-ferrous metals.
bright
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Al, AI and Mg alloys
Copper, brass, bronze
Cast iron materials
Order No.
1180
70
60
30
70
150
30
25
150
1180
1180
Drill ∅
Drill ∅
Order No.
PU
Order No.
PU
Shank ∅ h9 mm
Total length mm
For work- piece ∅ mm
Shank ∅ h9 mm
Total length mm
For work- piece ∅ mm
mm 3,15 4,00 5,00 6,30
mm 1,00 1,25 1,60 2,00 2,50
bright
bright
0100 0125 0160 0200 0250
28.10 31.00 29.80 32.40 36.50
10 3.15 31.5 6– 8 10 3.15 31.5 8–10 10 4.00 35.5 10–15 10 5.00 40.0 15–20 10 6.30 45.0 20–30
0315 0400 0500 0630
48.70 54.20 84.10
10 8.00 50.0 30– 40 10 10.00 56.0 40– 63 1 12.50 63.0 63–100 1 16.00 71.0 100–150
122.50
(108)
(108)
Solid carbide NC drilling device with cyl. Shank
Design: Solid carbide (K10/K20), type N, according to factory standard. Very sturdy model, profile grinding, right cutting, with precise point geometry and narrow cross blade. Without point thinning, with a clear side angle of 12°/30°. Angle of rake smaller than normal, core thickness much thinner than normal and normal core gradient. From ∅ 6 mm with carrier surface according to DIN 6535-HB. ∅ tolerance: up to ∅ 10 mm = h6, from ∅ 10 mm: cutting tolerance = h8. Application: 90° – For drilling and simultaneous countersinking if a spiral drill with a smaller ∅ follows. 142° –For intervening with the main blade of the following spiral drill. Especially suitable for precise positioning and fast boring on NC machines and jig boring machines. Used for centring and chamfering thread holes in one step. Only suitable for drilling.
Solid carbide K10/K20
Type N
Factory standard
DIN 6535-HB
90°
142°
Particularly suitable for high strength steels, steel castings, grey cast iron, hard castings, manganese hard steel, CrNi steels, bronzes and light and non-ferrous metals.
1170
90°
bright
1170/1174 bright
1174
142°
bright
1172
90°
TiAlN
1172/1176 TiAlN
1176
142°
TiAlN
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Al, AI and Mg alloys
Copper, brass, bronze
Cast iron materials
Order No.
1170 1172 1174 1176
60 65 60 65
50 55 50 55
70 90 70 90
100 100 180 200
160 180 160 180
30 35 30 35
25 30 25 30
35 40 35 35
1170
1172
1174
1176
∅ h6
Order No.
Slot length
Total length
mm
mm
mm 38 46 55 62 66 79 89 102 115 131
bright
TiAlN
bright
TiAlN
0200 0300 0400 0500 0600 0800 1000 1200 1600 2000
2 3 4 5 6 8
15.25 15.25 16.65 19.00 20.10 31.10 44.70 59.60 83.80
18.70 18.70 20.30 23.10 25.60 41.70 57.40 75.30
15.25 15.25 15.25 16.65 18.10 24.90 29.30 34.70 93.80
20.80 20.80 22.60 24.30 26.60 39.70 47.30 56.80
8
12 12 14 16 21 25 30 37 45
10 12 16 20
105.00 196.00
125.50 204.50
131.00
125.50
(108)
(108)
(108)
(108)
1/56
All stocked articles available within 24 hours by UPS Express.
All prices excluding VAT per piece (if not stated otherwise).
Made with FlippingBook