Catalog FORMAT plus - EDE 2015 - 2017

Milling Cutters 346

Solid Carbide 2 Flute Necked & Tapered Ball Nose Slot Drills

Design: Ultra-fine grit solid carbide, type N, according to company standard, 30°, Signum-coated, with centre cut. Cutting speed approx. 50 % higher than with non-coated tools. Dry machining possible. These tools should only be used in shrink or hydro-.expansion chucks. Application: Can be used for copy milling. The neck chip channel makes optimum tool range possible and thus makes it suitable for mould-making applications. Suitable for machining hardened mate- rials up to 54 HRC . Note: Copy milling; cutting values preferred at ap = 0.05 x d 1 and ae = 0.1 x d 1 .

Solid carbide UF

Z 2

Type N

Factory standard

DIN 6535-HA

30°

8°

2 Cutting Tools

Signum

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2486

200

200

180

160

120

160

90

200

100

6WHHOV XSWR +5F f z mm

2486

dia.

Order No.

Radius r ± 0.01 mm

Cutting edge length l 2 mm

Overall length l 1 mm

Neck ∅ d 3 mm

Clear area l 3 mm

Angle of taper in degrees

Shank dia. d 2 = h6 mm

d 1

= h8

mm

Signum

0020 0030 0040 0060 0080 0100 0120

2 3 4 6 8

97.60 69.70 74.90 90.60

1.0 1.5 2.0 3.0 4.0 5.0 6.0

3.0 3.5 4.0 6.0 7.0 8.0

80 80 80

1.8 2.8 3.8 5.6 7.6 9.6

40 40 40 60 75 70

2.9 2.2 1.4 1.0 0.8 0.8 1.2

6 6 6 8

0.030 0.040 0.045 0.050 0.070 0.100 0.120

100 120 120 150

110.00 146.50 251.00

10 12 16

10 12

10.0

11.5

100

(221)

Solid Carbide Long Series 2 Flute Necked Ball Nose Slot Drills

Design: Ultra-fine grit solid carbide, type N, according to company standard, 30°, Signum-coated, with centre cut. Cutting speed approx. 50 % higher than with non-coated tools. Dry machining possible. These tools should only be used in shrink or hydro-.expansion chucks. Application: Can be used for copy milling. The neck chip channel makes optimum tool range possible and thus makes it suitable for mould-making applications. Suitable for machining hardened materials up to 54 HRC . Note: Copy milling; cutting values preferred at ap = 0.05 x d 1 and ae = 0.1 x d 1 . Shrunk-fit chucks can be found on Ç 3/79.

Solid carbide UF

Z 2

Type N

Factory standard

DIN 6535-HA

30°

8°

Signum

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2488

200

200

180

160

120

160

90

200

100

6WHHOV XSWR +5F f z mm

2488

dia.

Order No.

Radius r ± 0.01 mm

Cutting edge length l 2 mm

Overall length l 1 mm

Neck ∅ d 3 mm

Clear area l 3 mm

Shank dia. d 2 = h6 mm

d 1

= h8

mm

Signum

0060 0080 0100 0120

6 8

61.90 70.60

3 4 5 6

6 7 8

80

1.8 2.8 3.8 5.6

45 65 80 75

6 8

0.050 0.070 0.100 0.120

100 120 120

10 12

116.50 152.50

10 12

10

(221)

2/100

All stocked articles available within 24 hours by UPS Express.

All prices excluding VAT per piece (if not stated otherwise).