Catalog FORMAT plus - EDE 2015 - 2017

353

Milling Cutters

Solid Carbide 4 Flute End Mill with Corner Radius for Hard Machining

Design: Solid carbide NANO, type H, according to company standard, 30°, TiAlN-S-coated, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. Application: Can be used for peripheral milling and slot cutting. Is also suitable for milling deep grooves thanks to the offset shaft. With corner radius to avoid notching effects on the workpiece. Less corner wear during slot cutting. Suitable for HSC machining up to 70 HRC .

Z 4

Type H

Solid carbide NANO

Factory standard

DIN 6535-HA

HSC

30°

7°

TiAlN-S

2 Cutting Tools

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2494

195

195

195

130

130

130

+DUG PDFKLQLQJ RYHU +5F f z mm

2494

dia. d 1 mm 1.0 1.0 1.5 1.5 2.0 2.0 2.5 3.0 3.5 4.0 5.0 6.0 8.0 10.0 12.0 16.0

Order No.

Corner radius r mm

Cutting edge length l 2 mm

Overall length l 1 mm

Neck dia. d 3 mm

Clear area l 3 mm

Shank dia. d 2 = h6 mm

TiAlN-S

0101 0100 0151 0150 0201 0200 0250 0300 0350 0400 0500 0600 0800 1000 1200 1600

22.00 32.30 22.00 32.30 19.95 29.20 29.20 29.20 29.20 29.20 29.20 29.20 37.00 55.40 76.50

0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.1 0.2 0.2 0.2 0.2 0.3 0.3

1.5 1.5 2.2 2.2 3.0 3.0 4.0 4.0 5.0 5.0 6.0 7.0 9.0

40 40 40 40 40 40 40 45 45 45 50 50 60 75 75 90

– – – –

– – – –

3 6 3 6 3 6 6 6 6 6 6 6 8

0.002 0.002 0.002 0.002 0.004 0.004 0.005 0.006 0.007 0.008 0.011 0.013 0.016 0.019 0.022 0.026

1.95 1.95 2.40 2.85 3.35 3.85 4.85 5.85 7.70 9.70

6 6 6 7 9 9

11 14 18 25 30 38

12.0 15.0 18.0

10 12 16

11.70 15.70

127.50

(212)

Solid Carbide 4 Flute End Mill with Corner Radius for Hard Machining

Design: Ultra-fine grit solid carbide, type N, according to company standard, 30°, TiAlN-coated, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. Application: Can be used for peripheral milling. With corner radius to avoid notching effects on the workpiece. Suitable for HSC machining up to 62 HRC .

Solid carbide UF

Z 4

Type N

Factory standard

DIN 6535-HA

HSC

30°

7°

TiAlN

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2436

133

82

82

82

55

50

133

25

6WHHOV XSWR +5F f z mm

2436

dia. d 1 mm 2.0 2.5 3.0 3.5 4.0 5.0 6.0 8.0 10.0 12.0

Order No.

Corner radius r mm

Cutting edge length l 2 mm

Overall length l 1 mm

Neck dia. d 3 mm

Clear area l 3 mm

Shank dia. d 2 = h6 mm

TiAlN

0200 0250 0300 0350 0400 0500 0600 0800 1000 1200

29.00 29.00 29.00 29.00 29.00 29.00 29.00 37.10 54.90 75.30

0.20 0.25 0.30 0.35 0.40 0.50 0.60 0.80 1.00 1.20

2.5 3.0 4.0 4.5 5.0 6.0 7.0

50 50 50 50 50 50 55 60 70 80

1.9 2.4 2.8 3.2 3.7 4.6 5.6 7.4 9.4

5 6 7 8 9

6 6 6 6 6 6 6 8

0.002 0.003 0.003 0.004 0.004 0.005 0.006 0.008 0.009 0.010

12 14 18 25 30

10.0 12.0 15.0

10 12

11.4

(212)

2/107

Articles marked ◊ are not held in stock, procurement is effected at short notice.

Not all items are available in every country.