Catalog FORMAT plus - EDE 2015 - 2017

355

Milling Cutters

Solid Carbide 4 Flute End Mill with Corner Radius for Hard Machining

Design: Ultra-fine grit solid carbide, type N, according to company standard, 30°, TiAlN-coated, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. Application: Can be used for peripheral milling. With corner radius to avoid notching effects on the workpiece. Suitable for HSC machining up to 70 HRC .

Solid carbide UF

Z 4

Type N

Factory standard

DIN 6535-HA

HSC

30°

7°

2 Cutting Tools

TiAlN

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2437

80

52

52

52

32

32

80

32

6WHHOV XSWR +5F f z mm

6WHHOV XSWR +5F f z mm

2437

2437

dia. d 1 = e8 mm

dia. d 1 = e8 mm

Order No.

Corner radius r mm

Cutting edge length l 2 mm

Order No.

Corner radius r mm

Cutting edge length l 2 mm

Overall length l 1 mm

Shank dia. d 2 = h6 mm

Overall length l 1 mm

Shank dia. d 2 = h6 mm

TiAlN

TiAlN

0300 0400 0402 0500 0502 0600 0602 0604 0800 0802 0804 0808 1000

3 36.50 4 36.50 4 36.50 5 36.50 5 36.50 6 36.50 6 36.50 6 36.50 8 46.80 8 46.80 8 46.80 8 51.00 10 69.10

0.3 0.3 0.5 0.3 0.5 0.3 0.5 1.0 0.3 0.5 1.0 2.0 0.3

12 15 15 20 20 20 20 20 25 25 25 25 30

50 50 50 60 60 60 60 70 70 70 70 70 90

6 0.002 6 0.003 6 0.003 6 0.005 6 0.005 6 0.007 6 0.007 6 0.007 8 0.010 8 0.010 8 0.010 8 0.010 10 0.012

1002 1004 1008 1202 1204 1206 1208 1602 1604 1608 2004 2006 2008

10 10 10 12 12 12 12 16 16 16 20 20 20

69.10 69.10 75.40 94.80 94.80 103.50 103.50 153.50 153.50 163.50 248.50 271.00 271.00

0.5 1.0 2.0 0.5 1.0 1.5 2.0 0.5 1.0 2.0 1.0 1.5 2.0

30 30 30 30 30 30 30 50 50 50 55 55 55

90 10 0.012 90 10 0.012 90 10 0.012 90 12 0.012 90 12 0.012 90 12 0.012 90 12 0.012 110 16 0.014 110 16 0.014 110 16 0.014 110 20 0.012 110 20 0.012 110 20 0.012

(212)

(212)

Solid Carbide Long Series Reduced Shank 4 Flute End Mill with Corner Radius for Hard Machining

Design: Ultra-fine grit solid carbide, type H, according to company standard, 45°, TiAlN-coated, with centre cut. Cutting speed approx. 50% higher than with non-coated tools. Dry machining possible. Application: Can be used for deep side milling, spiral milling and contour milling. With corner radius to avoid notching effects on the workpiece. The 45° spiral results in a soft and peeling cut and thus a high surface quality. Burr formation on the cutting edges is avoided. Suitable for HSC machining up to 62 HRC .

Solid carbide UF

Type H

Z 4

Factory standard

DIN 6535-HA

HSC

45°

1°

TiAlN

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Al, AI and Mg alloys

Copper, brass, bronze

Cast iron materials

Order No.

2495

242

242

242

242

178

178

110

150

242

6WHHOV XSWR +5F f z mm

2495

dia. d 1 mm

Order No.

Corner radius r mm

Cutting edge length l 2 mm

Overall length l 1 mm

Neck dia. d 3 mm

Clear area l 3 mm

Shank dia. d 2 = h6 mm

TiAlN

1000 1010 1200 1210 1410 1810 2210

10 10 12 12 14 18 22

75.90 75.90

0.5 1.0 0.5 1.0 1.0 1.0 1.0

15 15 18 18 21 27 33

130 130 150 150 160 180 200

7.5 7.5 9.5 9.5

19.2 19.2 22.2 22.2 25.2 31.2 37.2

8 8

0.021 0.021 0.025 0.025 0.030 0.038 0.047

108.00 108.00 126.00 230.00 334.00

10 10 12 16 20

11.5 15.5 19.5

(212)

2/109

Articles marked ◊ are not held in stock, procurement is effected at short notice.