html - Catalog FORMAT plus - 2017 - 2018

Hole punches 1280

Wad punches

Design: DIN 7200 A, made of special tool steel, drop-forged, with finely polished tip and powder-coated shaft. Hardened and tempered cutting edge, slightly conical interior for simple removal of cut-out. Application: For producing seals and sealing rings made of card, leather and rubber, etc.

7120

7120

∅ mm

∅ mm

Order No. 0016 0017 0018 0019 0020 0022 0024 0025 0026 0028 0030 0032 0035 0040

Order No. 0002 0003 0004 0005 0006 0007 0008 0009 0010 0011 0012 0013 0014 0015

2 3 4 5 6 7 8 9

3.43 3.43 3.43 3.43 3.43 3.54 3.54 3.66 4.08 4.52 4.83 5.70 5.90

16 17 18 19 20 22 24 25 26 28 30 32 35 40

7.10 7.45 7.90 8.30 9.25

10.50 12.60 13.45 14.45 14.95 16.70 20.40 21.50 30.10 (W572)

10 11 12 13 14 15

6.40 (W572)

Wad punch set

Design: Supplied in roll-up case.

7121

Set content ∅

Order No.

Number of hole punches Piece

Increasing

mm

mm

0010 0020

2–20 2–30

97.70

19 15

1 2

118.00 (W572)

Hole punch set

Design: Made of high-strength special steel, ground and finely polished hole punch inserts. For cutting soft materials (rubber, leather, felt, foam). Reinforced materials (metal sheet, glass fibre) up to 0.3 can also be punched. In sturdy metal case.

7126

Design

Order No. 0020

Set contents

11-piece

68.60

Punch from 3 to 20 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20 mm Holder

Hand Tools 7

0030

16-piece

105.00

Punch from 3 to 30 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30 mm Holder Punch from 3 to 40 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30, 32; 34; 36; 38; 40 mm Block holders Punch from 3 to 50 mm: Thread inserts 3; 4; 6; 8; 10 mm Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30, 32; 34; 36; 38; 40; 42; 44; 46; 48; 50 mm Block holders

7126 0020

7126 0030

0040

21-piece

170.50

0050

26-piece

225.00

7126 0040

7126 0050

0060

33-piece

396.00

Punch from 3 to 60 mm: Thread inserts 3; 4; 6; 8; 10 mm

Stick-on inserts 12; 14; 16; 18; 20; 22; 24; 26; 28; 30; 32; 34; 36; 38; 40, 42; 44; 46; 48; 50; 52; 54; 56; 58; 60 mm Block holders 11 to 60 mm

Holders 3 to 30 mm Circle cutter 500 mm

(W518)

7126 0060

7/20