Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro

Reamers 164

Ai nevoie de ajutor? Suntem aici pentru tine! 0799.402.346 / 0799.402.343 | format@rocast.ro

m

NC machine reamer

Design: HSS-E, dimensions similar to 212. Centring up to ∅ 3.70 mm on both sides with 90° full point, above with inner centring, with straight shank ∅ for standardised mounting in hydraulic expansion chucks and high accuracy chucks. The clamping accuracy is significantly improved due to the narrow tolerance of the shanks. With cylinder shank, tolerance h6. Bright surface. Reamer manufacturing tolerances: – full diameter and 1/10 mm dimensions H7, – 1/100 mm dimensions of ∅ 1.01 to 5.03 mm 0.00/+0.004 mm, over ∅ 5.03 mm 0.00/+0.005 mm. Application: For reaming through holes, because of the short trim cut (from 3.8 mm) conditionally suitable for reaming blind holes.

Factory standard

HSS

H7

Cutting Tools 1

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1539

35

35

35

20

1539

1539

Nominal ∅

Nominal ∅

Order No.

Cutting length mm

Total length mm

Shank ∅ h6 mm

Order No.

Cutting length mm

Total length mm

Shank ∅ h6 mm

mm

mm

bright

bright

0600 0700 0800 0900 1000 1100 1200 1300 1400 1500 1600 1700

6.00 7.00 8.00 9.00 10.00 11.00 12.00 13.00 14.00 15.00 16.00 17.00

76.00 78.50 79.50 82.00 82.80 86.90 88.00 92.50 99.10

16 16 16 20 20 20 20 22 22 22 25 25

100 100 100 100 120 120 120 130 130 130 150 150

8 8 8

1800 1900 2000 2200 2400 2500 2800 3000 3200 3600 4000

18.00 19.00 20.00 22.00 24.00 25.00 28.00 30.00 32.00 36.00 40.00

133.00 137.00 139.00 193.50 202.00 186.00 228.00 217.50 227.00 261.50 316.50 (W143)

25 25 25 25 25 25 25 25 25 25 25

150 150 150 160 180 180 180 200 200 200 200

18 20 20 20 20 20 25 25 25 25 25

10 10 12 12 14 14 16 16 18

107.50 110.00 132.00 (W143)

m

NC machine reamer

Design: HSS-E, dimensions similar to 212. Centring up to ∅ 3.70 mm on both sides with 90° full point, above with inner centring, with straight shank ∅ for standardised mounting in hydraulic expansion chucks and high accuracy chucks. The clamping accuracy is significantly improved due to the narrow tolerance of the shanks. With cylinder shank, tolerance h6. Bright surface. Reamer manufacturing tolerances: – full diameter and 1/10 mm dimensions H7, – 1/100 mm dimensions of ∅ 1.01 to 5.03 mm 0.00/+0.004 mm, over ∅ 5.03 mm 0.00/+0.005 mm. Application: For reaming through holes, because of the short trim cut (from 3.8 mm) conditionally suitable for reaming blind holes.

Factory standard

HSS

H7

bright

Steels up to 850 N/mm 2

Steels up to 1000 N/mm 2

Steels up to 1400 N/mm 2

Hard machining over 60 HRC

Ti steels, Ti alloys, special steels

Stainless and acid- resistant steels (INOX)

Steels up to 42 HRC

Steels up to 52 HRC

Steels up to 56 HRC

Steels up to 60 HRC

Copper, brass, bronze

Cast iron materials

Al, Al and Mg alloys

Order No. 1542

35

35

35

20

1542

1542

Nominal ∅

Nominal ∅

Order No.

Cutting length mm

Total length mm

Shank ∅ h6 mm

Order No.

Cutting length mm

Total length mm

Shank ∅ h6 mm

mm

mm

bright

bright

0600 0700 0800 0900 1000 1100 1200 1300

6.00 7.00 8.00 9.00 10.00 11.00 12.00 13.00

68.20 70.60 71.70 75.30 77.50 82.30 83.50 88.00 (W143)

16 16 16 20 20 20 20 22

100 100 100 100 120 120 120 130

8 8 8

1400 1500 1600 1700 1800 1900 2000

14.00 15.00 16.00 17.00 18.00 19.00 20.00

93.20

22 22 25 25 25 25 25

130 130 150 150 150 150 150

14 16 16 18 18 20 20

101.50 104.00 123.50 124.00 128.00 130.00 (W143)

10 10 12 12 14

Hydraulic chucks are found on Ç 3/81.

1/146

Made with FlippingBook Online document