Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro
Reamers 165
Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.
Carbide machine reamer
Design: Solid carbide up to nominal ∅ 9.0 mm, carbide (K10) from nominal ∅ 10.0 mm DIN 8093, with approx. 7° left spirals, with long cutting section, short point and uneven tooth pitch. This achieves clean and exact drilling. With cylinder shank Tolerance h7. Bright surface. Application: For reaming through-holes and also suitable for reaming blind holes due to the short point. Particularly suitable for high alloy and annealed steels up to 52 HRC, casting materials and soft non-ferrous metals such as aluminium and brass.
DIN 8093
H7
Carbide
approx. 7°
Cutting Tools 1
bright
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Copper, brass, bronze
Cast iron materials
Al, Al and Mg alloys
Order No. 1546
C
C
C
C
V
C
C
C
C
C
1546
1546
Nominal ∅
Nominal ∅
Order No.
Cutting length mm
Total length mm
Shank ∅ h9 mm
Order No.
Cutting length mm
Total length mm
Shank ∅ h9 mm
mm
mm
bright
bright
0100 0120 0140 0150 0180 0200 0220 0250 0280 0300 0320
1.0 1.2 1.4 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.2
25.50 27.00 27.00 22.80 32.30 26.40 34.40 30.40 35.50 31.30 36.80 (W146)
5.5 7.5 8.0 8.0 9.0 11.0 12.0 14.0 15.0 15.0 16.0
34 38 40 40 46 49 53 57 61 61 65
1.0 1.2 1.4 1.5 1.8 2.0 2.2 2.5 2.8 3.0 3.2
0350 0400 0450 0500 0600 0700 0800 0900 1000 1100 1200
3.5 4.0 4.5 5.0 6.0 7.0 8.0 9.0
35.00 36.10 42.40 43.60 52.90 63.30 66.90 76.10 54.60 68.10 62.60 (W146)
18.0 19.0 21.0 23.0 26.0 31.0 33.0 36.0 38.0 41.0 44.0
70 75 80 86 93 109 117 125 133 142 151
3.5 4.0 4.5 5.0 5.6 7.1 8.0 9.0 10.0 10.0 10.0
10.0* 11.0* 12.0*
*According to factory standard.
Carbide machine reamer
Design: Carbide (K10) DIN 8094, with approx. 7° left spirals, with long cutting section, short point and uneven tooth pitch.
DIN 8094
H7
Carbide
This achieves clean and exact drilling. With morse taper shank Bright surface.
MK 1–3
approx. 7°
Application: For reaming through-holes and also suitable for reaming blind holes due to the short point. Particularly suitable for high alloy and annealed steels up to 52 HRC, casting materials and soft non-ferrous metals such as aluminium and brass.
bright
Steels up to 850 N/mm 2
Steels up to 1000 N/mm 2
Steels up to 1400 N/mm 2
Hard machining over 60 HRC
Ti steels, Ti alloys, special steels
Stainless and acid- resistant steels (INOX)
Steels up to 42 HRC
Steels up to 52 HRC
Steels up to 56 HRC
Steels up to 60 HRC
Copper, brass, bronze
Cast iron materials
Al, Al and Mg alloys
Order No. 1549
C
C
C
C
C
C
C
C
C
1549
1549
Nominal ∅
Nominal ∅
Order No.
Cutting length mm
Total length mm
MK
Order No.
Cutting length mm
Total length mm
MK
mm
mm
bright
bright
1000 1100 1200 1300 1400 1500 1600 1700 1800
10 11 12 13 14 15 16 17 18
66.90 71.90 67.50 73.00 78.50 86.40 89.50 98.00 91.90 (W146)
38 41 44 44 47 50 52 54 56
168 175 182 182 189 204 210 214 219
1 1 1 1 1 2 2 2 2
1900 2000 2200 2400 2500 2600 2800 3000
19 20 22 24 25 26 28 30
109.50 102.50 117.50 146.00 146.00 161.00 202.50 189.50 (W146)
58 60 64 68 68 70 71 73
223 228 237 268 268 273 277 281
2 2 2 3 3 3 3 3
1/147
Articles marked ◊ are not held in stock, procurement is effected at short notice.
Made with FlippingBook Online document