Catalog FORMAT plus 2017 - 2018 | Contact : 0799.402.346 | 0799.402.343 | e-mail : format@rocast.ro

Digital dial gauges 773

Prețurile sunt orientative. Solicitați oferta și veți obține prețuri mult mai avantajoase.

m

Digital dial gauge for concentricity and evenness testing

Design: Clamping shaft and measuring bolts made of rustproof, hardened steel. Digit height on LCD display 8.5 mm, operating and display part can be rotated by 280°. With interchangeable stylus tips M2.5. Clamping shaft ∅ 8 mm, protective cap at end of measuring bolt. With data output via radio transmission, RS 232, USB and Digimatic. Supplied with battery CR 2450, 3 V. Functions: Automatic on and off switch, mm/inch switching, automatic activation by moving switch, key lock set for zero position, re-zeroing after switching deleted (absolute system), MAX/MIN storage for reversal point search, tolerance entry, ABS (switching from relative to absolute measurement), reset (zeroing) possible at each position, counting direction change, ± pre-set function (setting a numerical value). Note: Suitable measuring inserts M2.5 are found on Ç 4/49. .

Factory standard

Absolute function

IP 42

RS232

USB

Digimatic

Lifting cap (Order No. 4246 0165, Ç 4/54). Eyelet rear wall (Order No. 4246 0175, Ç 4/54). Radio receiver (Order No. 4942 0030, Ç 4/129). Transmitter module for e-Stick (Order No. 4942 0040, Ç 4/130). Data cable RS 232 (Order No. 4942 0055, Ç 4/130). Data cable USB (Order No. 4942 0050, Ç 4/130). Data cable Digimatic (Order No. 4246 0185, Ç 4/54).

4246

Measurement range mm

Order No. 0110 0120 0115 0125

Reading mm

Housing ∅ mm

Accuracy mm

With radio transmission

12.5 12.5 25.0 25.0

431.00 463.00 489.00 522.00 (W488)

0.0005 60.5 0.0005 60.5 0.0005 60.5 0.0005 60.5

0.004 0.004 0.004 0.004

–

•

–

•

Equipment

Measuring

4

m

Digital dial gauge

Design: Clamping shaft and measuring bolts made of rustproof, hardened steel. Digit height on LCD display 8.5 mm, operating and display part can be rotated by 280°. With interchangeable stylus tips M2.5. Clamping shaft ∅ 8 mm, protective cap at end of measuring bolt. With data output via radio transmission, RS 232, USB and Digimatic. Supplied with battery CR 2450, 3 V. Functions: Automatic on and off switch, mm/inch switching, automatic activation by moving switch, key lock set for zero position, re-zeroing after switching deleted (absolute system), MAX/ MIN storage for reversal point search, tolerance entry, ABS (switching from relative to absolute measurement), reset (zeroing) possible at each position, counting direction change, ± pre-set function (setting a numerical value). Application: The reversal point is automatically determined by a 2-point inside or outside measurement through oscillation, than a preset value can be simply assigned to it. During the measurement. the measured ACTUAL value is saved by the MIN or MAX function and shown in the display. In order to perform measuring movements with corresponding measuring accuracy, 64 measurement values are processed per second. Note: Suitable measuring inserts M2.5 are found on Ç 4/49.

Factory standard

Absolute function

IP 42

RS232

USB

Digimatic

Lifting cap (Order No. 4246 0165, Ç 4/54). Eyelet rear wall (Order No. 4246 0175, Ç 4/54). Radio receiver (Order No. 4942 0030, Ç 4/129). Transmitter module for e-Stick (Order No. 4942 0040, Ç 4/130). Data cable RS 232 (Order No. 4942 0055, Ç 4/130). Data cable USB (Order No. 4942 0050, Ç 4/130). Data cable Digimatic (Order No. 4246 0185, Ç 4/54).

4246

Measurement range mm

Order No. 0130 0135

Reading mm

Housing ∅ mm

Accuracy mm

With radio transmission

12.5 25.0

488.00 525.00 (W488)

0.0005 60.5 0.0005 60.5

0.004 0.004

–

•

4/53

Articles marked ◊ are not held in stock, procurement is effected at short notice.